About Us    New Product Ideas    Custom Mfg.    Contact	847-455-0188
4" Square Conduit Boxes   4" Square Boxes 1-1/2" Deep   4" Square Boxes 1-1/4" Deep   4" Square Boxes 2-1/8" Deep   4" Square Boxes 3-1/2" Deep   4" Square Bracket Boxes 1-1/2" Deep   4" Square Bracket Boxes 2-1/8" Deep   4" Square Extension Rings 1-1/2" Deep   4" Square Extension Rings 2-1/8" Deep   4" Square Flat Covers   4" Square Garvin Covers   4" Square Mud Rings 1 Gang   4" Square Mud Rings 2 Gang   4" Square Offset Mud Ring   4" Square Tile Covers 1 Gang   4" Square Tile Covers 2 Gang 4" Square to Round Device Rings   4" Swivel & Kwik-Hang Fixture Covers   Wire Protector Pans 4-11/16" Conduit Boxes Conduit Body Electrical Boxes & Covers Handy Boxes Electrical Boxes & Covers Masonry Electrical Boxes & Covers Multi-Gang Electrical Boxes & Covers Octagon & Round Electrical Boxes & Covers Stainless Steel Electrical Boxes & Covers Switch Boxes Electrical Boxes Plastic Fasteners, Hangers & Clamps Fire Alarm / Emergency Boxes & Covers Fittings, Hubs & Bushings Fixture Whips & Grips GFCI--Ground Fault Circuit Interrupters Grounding Products Lighting & Lamps & CFL Bulbs Service Entrance Products Switches, Devices & Receptacles Tools & Install Accessories Wall Plates Weatherproof Boxes & Covers Aerial Drop Wire Hardware Beam Clamps Bridle Rings Bulk Wire & Cable Cable Management Distribution Rings Fire Prevention Products J-Hooks Jacks, Face Plates & Bezels Patch Cables Rope, Twine & Pulling Tape   4" Square Conduit Boxes : 4" Square to Round Device Rings     PAGES:  1 | 2  8 Style(s) Available  4" Square-To-Round Cover Raised 1/2" 4" Square-To-Round Cover Raised 1/2" is used to convert a square opening to a round opening. Angled mounting ears, or slots, allow for up to 12° of box misalignment. Cover Size: 4” Raised: 1/2” Cubic Inches: 3.5 Ears: 2-3/4” Off Center Holes: Tapped #8-32 Material: Steel 4" Square-To-Round Cover Raised 5/8" 4" Square-To-Round Cover Raised 5/8" is used to convert a square opening to a round opening. Angled mounting ears, or slots, allow for up to 12° of box misalignment. Cover Size: 4” Raised: 5/8” Cubic Inches: 4.5 Ears: 2-3/4” Off Center Holes: Tapped #8-32 Material: Steel 4" Square-To-Round Cover FLAT 4" Square-To-Round Cover Raised Flat is used to convert a square opening to a round opening. Angled mounting ears, or slots, allow for up to 12° of box misalignment. Cover Size: 4” Raised: Flat Cubic Inches: -- Ears: 2-3/4” Off Center Holes: Tapped #8-32 Material: Steel 4" Square-To-Round Cover Raised 3/4" 4" Square-To-Round Cover Raised ¾” is used to convert a square opening to a round opening. Angled mounting ears, or slots, allow for up to 12° of box misalignment. Cover Size: 4” Raised: 3/4” Cubic Inches: 5.5 Ears: 2-3/4” Off Center Holes: Tapped #8-32 Material: Steel 4" Square-To-Round Cover Raised 1-1/4” 4" Square-To-Round Cover Raised 1-1/4” is used to convert a square opening to a round opening. Angled mounting ears, or slots, allow for up to 12° of box misalignment. Cover Size: 4” Raised: 1-1/4” Cubic Inches: 9.5 Ears: 2-3/4” Off Center Holes: Tapped #8-32 Material: Steel 4" Square-To-Round Cover Raised 1” 4" Square-To-Round Cover Raised 1” is used to convert a square opening to a round opening. Angled mounting ears, or slots, allow for up to 12° of box misalignment. Cover Size: 4” Raised: 1” Cubic Inches: 7.5 Ears: 2-3/4” Off Center Holes: Tapped #8-32 Material: Steel 4" Square-To-Round Cover Raised 1-1/2" 4" Square-To-Round Cover Raised 1-1/2” is used to convert a square opening to a round opening. Angled mounting ears, or slots, allow for up to 12° of box misalignment. Cover Size: 4” Raised: 1-1/2” Cubic Inches: 11.3 Ears: 2-3/4” Off Center Holes: Tapped #8-32 Material: Steel   PAGES:  1 | 2  8 Style(s) Available